Upholstery 101 (week 1)

Hello, and welcome. If you are new here, this is the first of a series of posts following my upholstery project. I hope you will join along, find a project, and dig in.....and if you only want to watch, that's OK too! For Week 2 go here; Week 3 go here; Week 4 go here; Week 5 go here; Week 6 go here; Week 7 go here; Week 8 go here; Week 9 go here; Week 10 go here; The Finale go here!



Every Wednesday, until it is finished, I will share a step-by-step tutorial of re-upholstering this chair


so let's begin.....

This week, I used these tools


a nail puller, safety glasses, a dust mask, razor blades (not shown) and a pair of needle-nose pliers

Before you start...take lots of pictures to reference back to later.

Stripping the chair. Using a combination of puller and pliers, remove trim, fabric, nails and/or staples





go slow, try not to rip the fabric too much you will need some of the pieces for a pattern when cutting your new fabric. Take pictures along the way and also take notes of the order pieces come off. You will most likely re-upholster in the reverse order.


Note: arm has piping and is under stuffed


Note: side has piping on both sides

Note: back has 3 pieces


Note: sides are hand sewn together...I probably will not put it back together this way. It is not necessary with today's products available....but I will be flexible, and make that decision at the time.

I used a razor blade (oops, not in my tools photo) to cut the hand sewing.


open side seam all the way down the back


the reason why the back has no support. Not enough strapping, and set on the inside


 when you get to the "insides" of the chair, decide if the webbing/burlap has enough integrity and is doing the job. In this case, the burlap has too much give and should be replaced.

 flip the chair over to get into hard to reach areas. Yes, remove the black fabric to examine the springs

 In this case, I can see that the webbing on the bottom of the chair needs to be re-attached...but I knew there was a problem with the support, because the seat sagged when I sat in it

 under the arm

 Note, the finished inside fabric was in 3 pieces....maybe because of pattern, maybe because there was not enough, maybe they liked the look. However, since the lining is one solid piece, I will consider making my finished chair with one piece, no seems. Yes, this gray fabric is coming off, I need to get to the stuffing

 Note, the reason why the arms were not soft, batting has worn down over time

 the inside back of my chair, no support, need to fix that, I will be adding foam as well as batting for the finished chair

 horsehair for the seat covered with batting. I have used horsehair and it is messy. It does have a more authentic look, I will be using foam & batting

 this edge roll is perfectly fine, I will remove it and save it for the new chair. However, as you can see, the burlap needs to be replaced


and here you are...a completely stripped chair. You may notice that one of the tassels along the top came off in the process. It was very loose and needs to be glued.

I SAVED all the fabric scraps/pieces, I THREW OUT all of the batting, horsehair, nails, trim and burlap.

Next time, I will examine the overall sturdiness of the chair....until then

10 comments:

Kim said...

Love this tutorial! Thank you ... I have always been convinced I can do this, now you are teaching me! Looking forward to next week ... i am looking for a chair to join in the project!

My Crafty Home-Life said...

I bet you have access to great "potential" chairs!

The Pink Pagoda said...

Wow. Your tutorials are very good. The directions and photos are so helpful!!

kelly@refresheddesigns. said...

Janet, so glad you pointed out these tutorials- so great and so helpful! Thanks.

My Crafty Home-Life said...

I'm glad you like them. I always wonder if anyone is reading this stuff! Thanks for letting me know

Manoj Singal said...

Thanks for sharing such useful information. The information provided here is very nice and this information is not available so easily. Therefore I thank the writer for share this useful input. I Love To Read Your Blog and it was Really Helpful for me and it gives good details.
Strapping Tools,

Manoj Singal said...

Thanks for sharing such useful information. The information provided here is very nice and this information is not available so easily. Therefore I thank the writer for share this useful input. I Love To Read Your Blog and it was Really Helpful for me and it gives good details.
Strapping Tools,

WWL said...

I am not a DYI person but I am enjoying reading about your project. If I have something reupolstered I will know the proper way it should be done.

My Crafty Home Life said...

Thanks!

Barbara Bussey {The Treasured Home} said...

Good heavens! Now I know why having furniture reupholstered is so expensive. You are a very patient person and have offered a wonderful tutorial! There's a fabric shop in the area that offers what I hear is a great class in upholstery work. But this is definitely not for whips! Thanks for the great info!
Cheers!,
Barbara

Related Posts Plugin for WordPress, Blogger...